ZANUSSI
REFRIGERATOR
ZRT 183W1
INSTRUCTION BOOK
GB
200381073
A/ZE/71. (07.)
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings or these warnings contact the Customer Care Department.
Prior to installation
Maintenance and Cleaning
Check the appliance for transport damage. Under
no circumstances should a damaged appliance be
installed. In the event of damage please contact
your retailer.
Before cleaning, always switch off the appliance
and disconnect from the electrical supply.
When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Installation
Servicing
This appliance is heavy. Care should be taken when
moving it.
This product should be serviced by an
authorised engineer and only genuine spare
parts should be used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local
Service Force Centre.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
Ensure that the appliance does not stand on the
electrical supply cable. If the supply cable is
damaged, it must be replaced by a cable available
from your local Service Force Centre.
Make sure that the power plug has not been
squashed or damaged during transit.
- A damaged power plug may overheat and cause a
fire.
At the end of the Appliance Life
When disposing of your appliance use an
authorised disposal site.
The symbol
As you unpack the appliance, check carefully
on the product or on its
for any signs of transit damage.
packaging indicates that this product may not be
treated as household waste. Instead it should be
taken to the appropriate collection point for the
recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
Do not place heavy articles or the
fridge/freezer itself on the power cord.
- There is a risk of a short circuit and fire.
Do not remove the power cord by pulling on its
lead, particularly when the fridge/freezer is
being pulled out of its niche.
- Damage to the cord may cause a short-circuit, fire
and/or electric shock.
- If the power cord is damaged, it must be replaced
by a certified service agent or qualified service
personnel.
If the power plug socket is loose, do not insert
the power plug.
- There is a risk of electric shock or fire.
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as stated in the installation
instructions.
Safety precautions for isobutane
Warning
The refrigerant isobutane (R 600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of
obstruction.
Do not use mechanical devices or other means
to accelerate the defrosting process, other than
those recommended by the manufacturer.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Child Safety
Do not allow children to tamper with the controls or
play with the product.
Keep packaging materials away from children, to
prevent the risk of suffocation!
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance.
During Use
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs. It is
not intended for commercial or industrial use.
3
The Appliance and the Environment
This appliance does not contain gasses which could
damage the ozone layer.
Avoid damaging the cooling unit.
The packaging used on this appliance marked with the
symbol is recyclable.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
4
CONTENTS
Instructions for the User
Guide to use the instruction book
Important Safety Instructions
Instructions for the Installer
2
3
Technical Specifications
12
Installing the Appliance
Transportation, Unpacking
Cleaning
Location
Ventilation Requirements
Levelling
12
12
12
12
13
13
13
Instructions for the User
General Information
Description of the Appliance
6
6
6
Door Reversal
Using the Appliance
Before Use
To Start the Appliance
Thermostat Control
Hints for storage
Storage Shelves
7
7
7
7
7
8
Electrical Connection
Storage Chart
15
16
Hints and Tips
Food Storage
Energy Saving Advice
8
8
8
Maintenance and Cleaning
Internal cleaning
External cleaning
Changing the Light Bulb
Defrosting Your Appliance
When the appliance is not in use
8
8
9
9
9
9
Something Not Working
Service and Spare Parts
Customer Care Department
Guarantee Conditions
10
10
11
11
5
INSTRUCTIONS FOR THE USER
To ensure correct operation, the appliance should
be located where the ambient temperature is
between 16-32 °C.
General information
This appliance is designed for the refrigeration of food
in a domestic home.
Description of the appliance
1. Glass shelf
10. Bottle shelf
11. Egg tray
2. Defrost water drain
3. Salad drawer
12. Air circulation
13. Spacer
4. Rating Plate
5. Adjustable feet
14. Condenser
15. Evaporator tray
16. Compressor
6. Butter compartment
7. Interior Light/Thermostat control knob
8. Door shelf
9. Door gasket
6
Using the Appliance
Before Use
Remove all securing tapes.
Wash the inside of the appliance with lukewarm water
with a little bicarbonate of soda added (5 ml to 0,5 litre
of water). Do not use soap or detergent as the smell
may linger. Dry the appliance thoroughly.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or products containing alcohol.
To Start the Appliance
)
1. Allow the appliance to stand for 2 hrs after
installation.
2. Plug in the appliance and switch on at the mains
supply.
3. Turn the thermostat control to the required setting.
A setting of 3 is usually suitable for normal
operation (see thermostat control).
4. Leave the appliance for approximately 4 hours for
the correct temperature to be reached before
placing food inside.
Thermostat Control
The thermostat control knob situated inside the
refrigerator regulates the temperature of the larder
compartment. Thermostat control is marked from 1-5
the higher the number, the colder the setting.
Position 0
Position 1
Position 5
-
-
-
Off
minimum coldness
maximum coldness
Hints for storage
Below is the recommended storage positions for
various food types:
1. Ready-cooked foods, convenience foods, fresh
meat, cold cuts
2. Milk, dairy products, foods in dishes
3. Fruits, vegetables, salads
4. Cheese, butter
5. Eggs
6. Yoghurt, sour cream
7. Small bottles, soft drinks
8. Large bottles, drinks
7
Storage Shelves
Energy Saving Advice
The variable shelves increase the usefulness of the
fresh food compartment. The shelves can be
rearranged by opening the door to 90°.
Do not install the cabinet close to sources of
heat, such as a cooker, dishwasher or radiator.
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
cabinet are not obstructed.
The door shelves can also be rearranged to your
requirements.
Always leave warm food to cool down to room
temperature before placing in the fridge.
Hints & Tips
Try to avoid keeping the door open for long
periods, or opening the door too frequently as
warm air will enter the cabinet, and cause the
compressor to often switch on unnecessarily.
Food Storage
To obtain the best results from your appliance
neither hot foods nor liquids which may evaporate,
should be placed in the larder compartment.
Ensure there are no obstructions preventing the
door from closing properly.
Keep the time between buying chilled food and
placing it in your fridge as short as possible.
It is advisable to periodically clean the
refrigeration system at the back of the appliance
with a duster or vacuum cleaner.
Do not push food together too much, try to allow air
to circulate around each item.
Do not store uncovered food.
Remove suspect food from your refrigerator and
clean, refer to cleaning and maintenance.
Maintenance & Cleaning
Before any maintenance of cleaning work is
carried out DISCONNECT the appliance from
the ELECTRICITY SUPPLY.
Internal Cleaning
Clean the inside and accessories with warm water and
bicarbonate of soda (5 ml to 0.5 litre of water). Rinse
and dry thoroughly.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or cleaning products containing
bleach or alcohol.
Clean the drain hole of the water trough at regular
intervals and ensure that the drain hole is clear at all
times. If blocked carefully clear using a piece of
flexible curtain wire inserted into the drain outlet to
remove the blockage.
Regularly check the door seals and wipe clean to
ensure they are clean and free from debris.
8
External Cleaning
Wash the outer cabinet with warm soapy water.
Do NOT use abrasive products.
There are sharp edges on the underside of
the product so care should be taken when
cleaning.
Once or twice a year dust the condenser (black grille)
and the compressor at the back of the appliance with
a brush or vacuum cleaner, as an accumulation of dust
will affect the performance of the appliance and cause
excessive electricity consumption.
Changing the Light Bulb
Should the light fail to work you can change it as
below:
Disconnect the appliance from the electricity supply.
Remove the lamp cover retaining screws, then take
the lamp cover off in the direction of the arrow and the
bulb can be changed. (Type of the bulb: 230 V, 15 W,
E 14 thread)
After changing the bulb replace the lamp cover, and
retaining screws and reconnect the appliance to the
electricity supply.
Defrosting Your Appliance
The fridge compartment is defrosted automatically,
when the motor stops. Defrost water from the cooling
plate runs out of the drain and onto a tray on the motor
compressor where it evaporates. Droplets of water on
the cooling plate during defrosting are quite normal
and will freeze on the plate afterwards.
When the appliance is not in use
When the appliance is not in use for long periods
disconnect from the electricity supply, empty all of the
food and clean the appliance, leaving the door ajar to
prevent unpleasant smells.
9
Something Not Working
If the appliance is not working correctly, please carry out the following checks before contacting your local
Zanussi Service Force Centre.
Problem
Possible Cause
No power at the socket.
Solution
No power to the
appliance
Check there is power at the socket.
There is a power cut.
Check there is not a power cut by checking the
household lights.
The fuse has blown.
Check the fuse has not blown.
Thermostat control knob is set at „0“.
The appliance is located in an unsuitable position.
Check the thermostat control knob setting.
The temperature in the
appliance is too high
Check the ambient temperature is within the
appliances operating limits of 16 °C to 32 °C.
The thermostat control is set too low.
Check that the thermostat control knob is turned to
the correct setting relative to ambient conditions.
The temperature in the
appliance is too low
The thermostat control knob is set too high.
Set the thermostat control knob to a warmer
position.
Excessive frost and ice
has built up
The door has been left open.
Something is obstructing the door.
The door gasket is dirty.
Check the door has not been left open.
Check nothing is preventing the door from closing.
Check the door gasket is intact and clean.
The appliance is not level.
Check if the appliance stands stable (all four feet
should be on the floor).
The appliance is noisy.
The drain hole is blocked.
Check the drain hole is not blocked (see
'Maintenance and Cleaning').
Water under the salad
drawer.
If after the above checks your appliance still does not
operate correctly, contact your local Service Force
Centre.
In-guarantee customers should ensure that the
above checks have been made, as the
engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
Please note that it will be necessary to provide proof
of purchase for any in-guarantee service calls.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
08705 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working."
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
10
Customer Care Department
For general enquiries concerning your Zanussi - Electrolux appliance or for further information on
Zanussi - Electrolux products, please contact our Customer Care Department by letter or telephone at the
Major Appliances - Customer Care Department
Zanussi - Electrolux
Addington Way
Luton
Bedfordshire
LU4 9QQ
08705 727727 (*)
*calls to this number may be recorded for training purposes.
Guarantee Conditions
We Zanussi - Electrolux undertake that if within 12
months of the date of the purchase this
ZANUSSI - ELECTROLUX appliance or any part thereof
is proved to be defective by reason only of faulty
workmanship or materials, the company will, at our option
repair or replace the same FREE OF CHARGE for labour,
materials or carriage on condition that:
The guarantee is in addition to your statutory and
legal rights.
EUROPEAN GUARANTEE
If you should move to another country within
Europe then your guarantee moves with you to your
new home subject to the following qualifications:
The appliance has been correctly installed and
used only on the electrical supply stated on the
rating plate.
The guarantee starts from the date you first
purchased your product.
The guarantee is for the same period and to the
same extent for labour and parts as exists in the
new country of use for this brand or range of
products.
The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer's instructions.
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
This guarantee relates to you and cannot be
transferred to another user.
Your new home is within the European
Community (EC) or European Free Trade Area.
All service work under this guarantee must be
undertaken by a Service Force Centre.
The product is installed and used in accordance
with our instructions and is only used
domestically, i.e. a normal household.
Any appliance or defective part replaced shall
become the Company's property.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest
Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your
move and able to look after you and your
appliances.
EXCLUSIONS
This Guarantee does not cover:
Damage or calls resulting from transportation,
improper use or neglect, the replacemet of any light
bulbs or removable parts of glass or plastic.
France
Germany Nurenberg
Senlis
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
Costs incurred for calls to put right an appliance
improperly installed or calls to appliances outside
the United Kingdom.
Italy
Pordenone +39 (0) 0434 39 4700
Sweden
UK
Stockholm
Luton
+46 (0) 8 672 53 90
+44 (0) 8705 727727
Appliances found to be in use within a commercial
environment, plus those which are the subject of
rental agreements.
Products of Zanussi - Electrolux manufacture
which are not marketed by Zanussi - Electrolux.
11
Instructions for the Installer
Technical Specifications
Model
ZRT 183W1
Gross capacity (l)
Net capacity (l)
Fresh food com.: 155
Fresh food com.: 152
Width (mm)
550
850
612
0,422
154
A
Height (mm)
Depth (mm)
Energy consumption (kWh/day)
(kWh/year)
Energy class, according to EU Standards
Rated current (A)
Noise Lc (dB)
0,55
38
Weight (kg)
33
Location
Installing the appliance
The appliance should be positioned in a well
ventilated, dry room.
Transportation, unpacking
The appliance and the interior fitting are protected for
transport.
Energy use is affected by the ambient temperature.
The appliance should therefore:
Remove all packaging and any adhesive tape.
not be installed next to radiators, cookers or
other sources of heat
Any remnants of adhesive can be removed using
white spirit.
only be installed at a location where the ambient
temperature corresponds to the climate
classification, for which the appliance is
designed.
After transportation the appliance must not be
switched on for 2 hours. This is to allow the
refrigerant to settle.
Cleaning
The climate classification can be found on the
serial plate.
Clean the accessories and the inside of the appliance
with warm water and bicarbonate of soda (5 ml
to 0.5 litres of water). Rinse and dry thoroughly.
The following table shows which ambient
temperature is correct for each climate
classification:
Do not use detergents, abrasive powders, highly
perfumed cleaning products, wax polishes or
cleaning products containing bleach or alcohol.
Climate Classification Ambient Temperature
SN
N
+10 to +32 °C
+16 to +32 °C
+18 to +38 °C
ST
12
Ventilation Requirements
The appliance must have adequate ventilation to
ensure correct operation.
Diagram shows the ventilation requirements when
installed:
A* Under a worktop, or cupboard.
* The clearance space of 10 cm above the appliance
may be reduced to 5 cm providing a clearance
space 2.5 cm is left on either side of the appliance.
B When freestanding
Levelling
The appliance must be level. Level the appliance by
adjusting the two adjustable feet (1) at the front of the
appliance.
If required the washer (2) can be removed.
2
1
Door Reversal
If required the opening direction of the door can be
changed as follows:
To reverse the bottom hinge assembly proceed as
follows:
Disconnect the appliance from the electricity
supply.
Tilt the appliance backwards, resting the top edge
of the appliance on a stool or something similar.
Unscrew the adjustable feet situated on both sides
at the front (2 pieces). Remove the lower door
hinge plate by unscrewing the 3 retaining screws.
Remove the hinge pin from the bottom of the door.
Slot the hinge pin into the hole in the hinge plate
and relocate the hinge assembly to the opposite
location and refit using the retaining screws.
Put the cabinet in the upright position.
13
To reverse the top hinge assembly proceed as follows:
Remove the 2 worktop retaining screws from the
back of the appliance.
Slide the worktop towards the rear and lift clear of
the appliance.
Remove the 2 upper hinge plate retaining screws.
Remove the hinge plate from the top of the door.
Unscrew the hinge pin from the hinge plate and re-
insert on the opposite side of the pate.
Rotate the hinge assembly 180° and insert the
hinge assembly into the opposite location.
Refit the 2 hinge plate retaining screws.
Relocate the worktop and refit the worktop
retaining screws.
To reverse the handle proceed as follows:
Remove screw covers (if fitted) and handle retaining
screws. Remove blanking plugs on the opposite
side using a punch.
Relocate the handle to the opposite side and refit
retaining screws (covers if fitted), and push the
plastic plugs supplied with the instruction book into
the holes where the handle was previously fitted.
14
Electrical Connection
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability should
these safety measures not be observed.
Electrical Requirements
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug
supplied, a 13 amp ASTA approved (BS 1362) fuse
must be used. Should the plug need to be replaced
for any reason. The wires in the mains lead are
coloured in accordance with the following code:
Green and Yellow:
Blue:
Brown:
Earth
Neutral
Live
The wire coloured green and yellow must be
connected to the terminal marked with the letter “E“ or
by the earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal “N“ or coloured black.
The wire coloured brown must be connected to the
terminal marked “L“ or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must
be secure over the outer sheath.
Important!
The plug must still be accessible after the
appliance has been installed.
The appliance should not be connected to the
electrical supply by means of an extension cable.
In case that the electrical cable has to be
replaced, please contact your local Service Force
Centre.
Warning!
A cut off plug inserted into a 13 amp socket is a
serious safety (shock) hazard. Ensure that it is
disposed of safely.
This appliance complies with the following
E.E.C. Directives:
73/23 EEC of 19.02.73 (Low Voltage Directive)
and subsequent modifications,
89/336 EEC of 03.05.89 (Electromagnetic
Compatibility
modifications.
Directive)
and
subsequent
15
Storage time chart
Time and method of storage of fresh foods in the refrigerator
Foods
Storage time in days
Method of packaging
1
X
X
X
X
X
X
2
X
X
X
3
x
X
X
4
x
x
x
5
x
x
x
6
7
Raw meat
cling film, airtight
dish covered
dish covered
dish covered
dish covered
cling film, cellophane, grease-
proof paper
Cooked meat
Roasted meat
Raw minced meat
Cooked minced meat
Cold cuts
x
X
X
x
x
x
x
Fresh fish
Cooked fish
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
x
X
x
x
x
x
cling film, airtight
dish covered
dish covered
cling film, airtight
dish covered
cling film, airtight
dish covered
original packaging
original packaging
original packaging
plastic box
plastic box
aluminium foil
cling film
x
Tinned fish, open
Fresh chicken
Fried chicken
Fresh duck, goose
Roasted duck, goose
Butter unopened
Butter opened
Milk
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
x
X
X
X
X
x
X
x
X
X
X
X
x
x
x
X
X
X
x
x
x
x
x
x
x
x
X
X
x
x
X
X
X
X
x
Cream
Sour cream
x
X
X
X
X
x
X
x
X
X
X
x
x
X
x
x
X
x
x
X
x
Cheese (hard)
Cheese (soft)
Egg
Spinach, sorrel
Green peas, green beans
Mushroom
Carrot
Tomato
Cabbage
Fruits: strawberries,
raspberries, etc.
Tinned fruits opened
Cakes filled with cream
X
X
X
cling film
cling film
cling film
cling film
cling film
cling film
cling film
x
x
X
X
X
x
x
x
X
X
x
X
X
x
X
X
X
X
X
x
x
x
x
dish covered
dish covered
Notation:
X
x
recommended storage time
maximum recommended storage time
16
© Electrolux plc 2007
ELECTROLUX HOME PRODUCTS OPERATIONS EUROPE
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux
Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of
approx. USD 14 billion in more than 150 countries around the world.
|