REFRIGERATOR-
FREEZER
ZRB 3225 X
USER MANUAL
2223 453-01
Disposal of old Appliances
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local council, your
household waste disposal service or the shop where
you purchased the product.
CONTENTS
Instructions for the User
Instructions for the
Installer
2
4
Important Safety Information
13
14
Technical Specification
Operation
Installation
Positioning
Before use
4
4
4
4
4
4
4
5
5
5
5
5
6
6
6
Control panel
14
14
Starting your appliance
Setting the temperature
Ambient Temperature Switch
The freezer compartment
Freezing fresh food
Frozen food storage
Thawing
Shelf holders
15
16
Electrical Connection
Rear Spacers
16
Door Reversal
Making ice cubes
Cold accumulators
Fresh food refrigeration
Movable shelves
Positioning the door shelves
Freezing calendar
7
Hints and Tips
8
8
8
8
8
9
Maintenance and Cleaning
Internal cleaning
External cleaning
When the appliance is not in use
Changing the light bulb
Defrosting
10
11
11
12
Something Not Working
Service and Spare Parts
Customer Care
Guarantee Conditions
3
OPERATION
Before using
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Control panel
S
4
1
3
2
A
C
D
B
A. Pilot light for ambient temperature switch
B. Ambient temperature switch
C. Operating pilot light
that because a very low temperature has been
selected, the motor is working continuously, which
prevents the defrost cycle from operating.
To ensure correct defrosting, min should be selected
on the thermostat and you should notice that the
motor cuts out from time to time, which is correct.
D. Thermostat control knob
Starting your appliance
Insert the plug into the wall socket.
The operating pilot light (C) will illuminate.
If you wish to return to a lower temperature, turn the
thermostat towards max, however you should turn
the setting lower occasionally to allow automatic
defrosting.
Setting the temperature
Ambient Temperature Switch
The temperature within the appliance is controlled by
the thermostat control knob situated at the top of the
appliance.
Low Ambient Temperature Switch
To ensure that the appliance is working efficiently
when the room temperature drops below 16°C, the
switch mounted on the control panel should be
pressed.
To operate the appliance proceed as follows:
Turn the thermostat control beyond the «I» position.
Position 1 = minimum coldness
No damage can be caused by leaving the switch in
this position for any period of time (see page 10 Low
ambient operation). However should the temperature
rise above 16°C remember to press again the switch.
Position 4 = maximum coldness
Turn the thermostat dial to the required position.
The intermediate position is usually the most
suitable.
The freezer compartment
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
The four-star freezer compartment is suitable for
storage of commercially frozen food and for freezing
fresh foods.
– room temperature
Freezing fresh food
– how often the door is opened
– how much food is stored
– position of the appliance
When freezing large amounts of fresh food turn the
thermostat to maximum approximately 1 hour prior to
freezing. When the food is frozen return the
thermostat back to the normal position.
Important
In any 24 hours you can freeze up to 9 kg. of fresh
food.
If the fridge is not defrosting correctly, it is possible
4
Place food to be frozen in the upper drawer of the
freezer as this is the coldest part.
Making ice cubes
The appliance is provided with one or more trays for
ice-cubes trays.
Frozen food storage
Fill the tray(s) 3/4 full to give the ice space to expand
and place them in the freezer compartment.
When first starting-up or after a period of non use,
before putting the food in the compartment let the
appliance run for at least two hours on the coldest
setting, then turn the thermostat knob to the normal
operating position.
To release the ice cubes simply give the tray a slight
twist.
Do not use sharp or metallic instruments to remove
the trays from the freezer.
Do not exceed the storage period indicated by the
food manufacturer.
Cold accumulators
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
The freezer contains two cold accumulators. Place
the cold accumulators in the FAST FREEZE
compartment. The cold accumulators increase
storage times in the event of a power cut or
breakdown.
Important
Do not put carbonated liquids, (fizzy drinks etc.), in
the freezer compartment.
Removal of these units wll increase the capacity of
the fast freezing compartment but will reduce
storage times in the event of a power cut or
breakdown.
Ice Iollies, if consumed immediately after removal
from the freezer, can cause low temperature skin
burns.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
“frost/freezer burns”.
Fresh food refrigeration
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Important
In the event of a power cut do not open the door. The
food in the freezer will not be affected if the power
cut is short and if the freezer is full. Should the food
begin to thaw, it must be consumed quickly and must
not be re-frozen. (See “Hits and Tips”)
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Thawing
Raw meat (beef, pork, lamb & Poultry): wrap in
polythene bags and place on the glass shelf on the
top of the salad crispers.
Frozen food, prior to being used, can be thawed in
the fridge or at room temperature depending on the
time available. Small food items may even be cooked
from frozen; in this case cooking will take longer.
Meat can only be stored safely in this way for
one or two days at the most.
Any frozen food which is allowed to thaw accidentally
should either be eaten as soon as possible or thrown
away. Alternatively, if the food is uncooked and has
not been completely defrosted it can be cooked and
then refrozen.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the salad crispers.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Meat, fish and fruit should be thawed in the
refrigerator compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
oven instructions, particularly regarding the
placement of aluminium wrapping or containers in
the oven.
Defrosted cooked food must never be refrozen.
5
Movable shelves
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
D338
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To do this proceed as shown in the diagram.
Freezing Calendar
The symbols show different types of frozen goods.
The numbers indicate storage times in months for the appropriate types of frozen goods.
6
HINTS AND TIPS
Energy Saving Advice
Normal Operating Sounds
•
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, and to the cooling
plate/evaporator.
•
•
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
•
•
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
•
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages
before placing them in the freezer.
A thermostat controls the compressor, and you
will hear a faint ’click’ when the thermostat cuts in
and out.
•
•
Always leave warm food to cool down to room
temperature before placing in the fridge.
Food Storage
Food which is to be frozen (when cool) should be
placed in the fridge before being transferred to
the freezer.
To obtain the best performance from your fridge-
freezer
•
•
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of
the refrigeration unit.
•
•
Do not store warm food or evaporating liquids.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container is
advisable. When you arrive home place the frozen
food in the freezer immediately.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
•
•
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
•
Ensure there are no obstructions preventing the
door from closing properly.
Do not push food together too much, try to allow
air to circulate around each item.
In the Event of a Power Failure
•
•
Do not store uncovered food.
If there is a power failure during the storage of frozen
foods, keep the door closed. If the temperature within
your freezer should rise, do not refreeze the food
without checking its condition. The following
guidelines should assist you:
Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
•
•
•
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
Ice-cream: Once thawed should be discarded.
Lean food keeps better and longer than fatty food,
salt reduces the storage time.
Fruits & Vegetables: If soft should be cooked and
used up.
Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airtight seal .
Breads & Cakes: Can be refrozen without danger.
Shellfish: Should be refrigerated and used up
quickly.
•
Packaging which is swollen or has traces of
refrozen water droplets on the pack could indicate
that the product has not been kept at a suitable
temperature and that it may have lost its original
quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage times indicated by the
manufacturer.
Cooked Dishes: i. e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: Can be refrozen providing
there are still ice crystals remaining within them.
Small Joints: Should be cooked and can then be
refrozen as cooked dishes.
Chicken: Should also be cooked and refrozen as a
fresh dish.
7
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Changing the light bulb
If it becomes necessary to replace the lamp, press on
the rear hook and at the same time slide the cover in
the direction indicated by the arrow.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED
CLEANING PRODUCTS OR WAX
POLISHES,TO CLEAN THE INTERIOR AS
THESE WILL DAMAGE THE SURFACE AND
LEAVE A STRONG ODOUR.
External cleaning
Unscrew the bulb and replace it with one of the same
power (the maximum power is shown on the light
diffuser).available from your nearest Service Force
Centre.
Replace the light cover by sliding it into its original
position.
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
You MUST ensure that the appliance is switched
OFF.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
PR259
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
8
Defrosting
Refrigerator
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via a
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
D037
Freezer
When the frost has reached a thickness of up to
4mm it can be removed using the ice scraper
provided with the appliance. During this operation it
is not necessary to disconnect the appliance from
the mains and remove the food. Never use metal
tools for this operation.
For complete defrosting (once or twice a year)
proceed as follows:
-
turn the thermostat dial to the «OFF» position (G)
or disconnect the appliance from the mains.
-
Remove any food from inside the freezer and
fridge, wrap it in several sheets of newspaper and
store in a cool,dry place.
-
Leave the door open and insert the ice scraper
under the channel in the centre of the lower part
of the appliance; place a low-sided container
beneath the scraper to collect the water (see fig.).
-
-
-
Clean and dry thoroughly.
Replace the scraper in one of the drawers .
Reconnect the appliance to the mains or reset
the thermostat to the normal position.
-
After letting the appliance run for at least half an
hour, replace the previously removed food into
the compartment.
D068
Important
When defrosting the freezer, the fridge is also
controlled by the thermostat and will not be
operational during this period. A temperature rise of
the frozen food packs, during defrosting, may
shorten their safe storage life.
9
SOMETHING NOT WORKING
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made, even if the appliance is under guarantee.
Before contacting your local Service Force Centre, check the following points:
Symptom
Solution
No power to the appliance
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come on
Ensure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
The temperature in the fridge or freezer section is
too high
Check the thermostat control knob is turned to the
correct setting relative to ambient conditions.
Check the ambient temperature is within the
appliance’s operating limits, please refer to the
installation section in this instruction book.
Relocate the appliance if necessary.
The freezer door will not open
Has door just been opened? If so leave for a few
minutes to allow the air pressure to equalise.
The compressor runs continously
Adjust the thermostat control knob to give correct
temperature control. See “Setting the temperature”.
Check that the doors are closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Check that air ventilation is not obstructed.
Excessive frost and ice has built up
Ensure the doors are not left open.
Check that nothing is preventing the doors from
closing.
Is the door gasket intact and clean.
Has advised periodic defrosting been carried out.
Noise
Refer to normal operating sounds.
Water under the salad crispers
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
Low ambient operation
During prolonged periods of low ambient temperatures,ie;10°C and lower, the compressor on single
compressor fridge freezers can remain inoperative during this time .
10
This is due to the air temperature within the refrigerator compartment being maintained at 6°C or under thus not
calling the thermostat to energise the compressor .
During a normal night time period of approximately 8 hours a traditional fridge freezer can normally maintain the
frozen food temperature but if the appliance is left for longer period in a low ambient temperature the freezer will
defrost .
If, after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:-
0 8 7 0
5
9 2 9 9 2 9
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi-Electrolux appliance or for further information on
Zanussi-Electrolux products, please contact our Customer Care Department by letter or telephone at the
Customer Care Department
Zanussi-Electrolux Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 727 727 (*)
* calls to this number may be recorded for training purposes.
11
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this
ZANUSSI-ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty
workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour,
materials or carriage on condition that:
•
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
•
•
•
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi-Electrolux manufacture which are not marketed by Zanussi-Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
•
•
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
•
•
•
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
•
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 29
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)8705 727727
+353 (0)1 4090751
Nürnberg
Pordenone
Stockholm
Luton
Sweden
UK
Ireland
Dublin
12
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
185
cm
Width
Depth
60
cm
cm
62,5
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
230-240 V / 50 Hz
140 W
AVERAGE DAILY UNITS ELECTRICITY *
GROSS CAPACITY
0.879
kWh
Fridge
222 l
86 l
Freezer
NET CAPACITY
Fridge
221 l
82 l
Freezer
STAR RATING
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
13
INSTALLATION
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on “Door reversal”.
Important
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located at the left on the inside of the
appliance.
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
The following table shows which ambient
temperature is correct for each climate classification:
SN +10°C to + 32°C
N
+16°C to + 32°C
ST +18°C to + 38°C
+18°C to + 43°C
T
A
B
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10°C (50°F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
NP008
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4”) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
D200
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers or a tool (see figure).
A
Shelf holders
Your appliance is equipped with shelf retainers that
make it possible to secure the shelves during
transportation.
B
To remove them proceed as follows:
Move the shelf retainers in the direction of the arrow,
raise the shelf from the rear and push it forward until
it is freed and remove the retainers.
C
14
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
WARNING:THIS APPLIANCE MUST BE
EARTHED.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green andYellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
BROWN
BLUE
CORD CLAMP
D207
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
15
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then re-tighten the screws.
Door reversal directions
1. Disconnect from the electricity supply.
D594
2. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
E
3. Remove the ventilation grill (D).
E
4. remove the bottom hinge (E) by unscrewing its
fixing screws;
F
F
5. Remove the freezer door by releasing it from the
middle hinge (H).
D
6. Unscrew the middle hinge.
7. Remove the fridge door by releasing it from the
top hinge pin (G).
F
8. Remove the pin then mount these on the side,
after having removed the small plugs which
should then be fitted on the opposite side.
H
9. reassemble the door;
10. using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge;
11.Refit the fridge door and replace the middle hinge
to the left hand side.
12.reassemble the lower hinge (E) on the opposite
side, using the screws previously removed. Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;
13.refit the ventilation grille (D), clipping it into place;
14. Unscrew the handles. Refit them on the opposite
side after having pierced the plugs with a punch.
Cover the holes left open with the plugs supplied
in the documentation pack.
G
The doors can be aligned by adjusting the middle
hinge.
The middle hinge can be adjusted horizontally, after
having slackened the two screws with a screwdriver.
Important
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
PR228
16
|