REFRIGERATOR-
FREEZER
ZE 76/3 W
INSTRUCTION BOOKLET
2222 003-97
CONTENTS
Instructions for the User
Instructions for the
Installer
2
4
5
Important Safety Information
Description of the Appliance
15
16
Technical Specification
Installation
Positioning
Operation
16
16
Before use
5
5
5
5
5
5
5
6
6
6
6
6
7
7
7
8
Rear Spacers
Control panel
Starting your appliance
Setting the temperature
Ambient Temperature Switch
The freezer compartment
Freezing fresh food
Frozen food storage
Thawing
17
18
Electrical Connection
Door Reversal
Making ice cubes
Cold accumulators
Fresh food refrigeration
Movable shelves
Positioning the door shelves
CRISPÕN FRESH
Cool Check Guide
9
Hints and Tips
10
Maintenance and Cleaning
Internal cleaning
10
10
10
10
10
11
External cleaning
When the appliance is not in use
Changing the light bulb
Cleaning CrispÕn fresh filter
Defrosting
12
13
13
14
Something Not Working
Service and Spare Parts
Customer Care
Guarantee Conditions
2222 003-97
3
DESCRIPTION OF THE APPLIANCE
A
B
C
D
E
K
J
I
H
AST FREEZE
F
G
F
A- Control panel
B- Interior light
C- Dairy compartment
D- Can storage shelves
E- Bottle storage shelf
F- Frozen food storage compartment
G- Freezing fresh food compartment
H- Salad crispers
I - Glass shelf with CrispÕn fresh filter
J- Cool Check Temperature Guide
K- Storage shelves
4
OPERATION
Before using
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Control panel
N
A
A. Pilot light for ambient temperature switch
B. Ambient temperature switch
B
C D
C. Thermostat knob
D. Operating pilot light
Starting your appliance
Insert the plug into the wall socket.
The operating pilot light (D) will illuminate.
Setting the temperature
that the motor cuts out from time to time, which is
correct.
If you wish to return to a lower temperature, turn the
thermostat to a higher number, however you should
turn the setting lower occasionally to allow automatic
defrosting.
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and an
ÒOFFÓ (O) position.
Ambient Temperature Switch
Position 1 = minimum coldness
Position 6 = maximum coldness
Low Ambient Temperature Switch
To ensure that the appliance is working efficiently
when the room temperature drops below 16¡C, the
switch mounted next to the thermostat control should
be switched to S.
Insert a coin to turn the thermostat dial to the
required position.
The intermediate position is usually the most
suitable (3-4).
No damage can be caused by leaving the switch in
this position for any period of time (see page 12 Low
ambient operation). However should the temperature
rise above 16¡C remember to turn the switch back to
N.
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
Ð room temperature
Ð how often the door is opened
Ð how much food is stored
Ð position of the appliance
The freezer compartment
The four-star freezer compartment is suitable for
storage of commercially frozen food and for freezing
fresh foods.
Important
Freezing fresh food
If the fridge is not defrosting correctly, it is possible
that because a very low temperature has been
selected, the motor is working continuously, which
prevents the defrost cycle from operating.
When freezing large amounts of fresh food turn the
thermostat to maximum approximately 1 hour prior to
freezing. When the food is frozen return the
thermostat back to the normal position.
To ensure correct defrosting, a lower number should
be selected on the thermostat and you should notice
5
In any 24 hours you can freeze up to 10 kg. of fresh
food.
oven instructions, particularly regarding the
placement of aluminium wrapping or containers in
the oven.
Place food to be frozen in the upper drawer of the
freezer as this is the coldest part.
Defrosted cooked food must never be refrozen.
Frozen food storage
Making ice cubes
The appliance is provided with one or more trays for
ice-cubes trays.
When first starting-up or after a period of non use,
before putting the food in the compartment let the
appliance run for at least two hours on the coldest
setting, then turn the thermostat knob to the normal
operating position.
Fill the tray(s) 3/4 full to give the ice space to expand
and place them in the freezer compartment.
To release the ice cubes simply give the tray a slight
twist.
Do not exceed the storage period indicated by the
food manufacturer.
Do not use sharp or metallic instruments to remove
the trays from the freezer.
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
Cold accumulators
Important
The freezer contains two cold accumulators. Place
the cold accumulators in the FAST FREEZE
compartment. The cold accumulators increase
storage times in the event of a power cut or
breakdown.
Do not put carbonated liquids, (fizzy drinks etc.), in
the freezer compartment.
Ice Iollies, if consumed immediately after removal
from the freezer, can cause low temperature skin
burns.
Removal of these units wll increase the capacity of
the fast freezing compartment but will reduce
storage times in the event of a power cut or
breakdown.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
Òfrost/freezer burnsÓ.
Fresh food refrigeration
Important
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
In the event of a power cut do not open the door.
The food in the freezer will not be affected if the
power cut is short and if the freezer is full. Should
the food begin to thaw, it must be consumed quickly
and must not be re-frozen. (See ÒHits and TipsÓ)
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
Thawing
To help you use your refrigerator correctly, here are
some more useful hints:
Frozen food, prior to being used, can be thawed in
the fridge or at room temperature depending on the
time available. Small food items may even be
cooked from frozen; in this case cooking will take
longer.
Raw meat (beef, pork, lamb & Poultry): wrap in
polythene bags and place on the glass shelf on the
top of the salad crispers.
Meat can only be stored safely in this way for
one or two days at the most.
Any frozen food which is allowed to thaw
accidentally should either be eaten as soon as
possible or thrown away. Alternatively, if the food is
uncooked and has not been completely defrosted it
can be cooked and then refrozen.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the salad crispers.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Meat, fish and fruit should be thawed in the
refrigerator compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
6
Movable shelves
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
For better use of space, the front half-shelves can lie
over the rear ones.
D338
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To do this proceed as shown in the diagram.
PR260
PR263
Use and features of the CRISPÕN
FRESH filter
ÒCrispÕn freshÓ is the glass shelf on top of the salad
crispers which is fitted with a special removable
green filter.
The filter allows cool air from the fridge to circulate
through the drawers and help prevent moisture loss.
By retaining moisture in foods such as fresh fruit,
vegetables and salad, they are kept fresher for
longer.
D749
7
Cool Check Guide
The guide consists of a temperature sensitive strip
sealed in a shelf trim.
When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.
TOO WARM
Positioning of the Cool Check
The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.
If the Cool Check shows TOO WARM
In certain conditions the temperature guide may
show TOO WARM if:
¥
¥
¥
The fridge is switched off
ZANUSSI
The door has been recently opened
A quantity of warmer food has been introduced to
the fridge
CCOO2
¥
The fridge temperature is above the
recommended maximum for the safe storage of
food.
The cool check will change to show ÒTOO WARMÒ
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.
The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the thermostat to a colder
setting leave overnight and examine again the
following morning.
Hints and Tips
¥
¥
¥
The guide is only suitable for use in the model
supplied.
The guide will not operate in the freezer
compartment.
When cleaning the shelf take care not to immerse
in water, and wipe away any spills.
8
HINTS AND TIPS
Energy Saving Advice
Normal Operating Sounds
¥
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, and to the cooling
plate/evaporator.
¥
¥
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
¥
¥
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
¥
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages
before placing them in the freezer.
A thermostat controls the compressor, and you
will hear a faint ÕclickÕ when the thermostat cuts in
and out.
¥
¥
Always leave warm food to cool down to room
temperature before placing in the fridge.
Food Storage
Food which is to be frozen (when cool) should be
placed in the fridge before being transferred to
the freezer.
To obtain the best performance from your fridge-
freezer
¥
¥
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of
the refrigeration unit.
¥
¥
Do not store warm food or evaporating liquids.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container
is advisable. When you arrive home place the
frozen food in the freezer immediately.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
¥
¥
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
¥
Ensure there are no obstructions preventing the
door from closing properly.
Do not push food together too much, try to allow
air to circulate around each item.
In the Event of a Power Failure
¥
¥
Do not store food uncovered.
If there is a power failure during the storage of frozen
foods, keep the door closed. If the temperature
within your freezer should rise, do not refreeze the
food without checking its condition. The following
guidelines should assist you:
Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
¥
¥
¥
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
Ice-cream: Once thawed should be discarded.
Lean food keeps better and longer than fatty
food, salt reduces the storage time.
Fruits & Vegetables: If soft should be cooked and
used up.
Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airtight seal .
Breads & Cakes: Can be refrozen without danger.
Shellfish: Should be refrigerated and used up
quickly.
¥
Packaging which is swollen or has traces of
refrozen water droplets on the pack could
indicate that the product has not been kept at a
suitable temperature and that it may have lost its
original quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage times indicated by the
manufacturer.
Cooked Dishes: i. e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: Can be refrozen providing
there are still ice crystals remaining within them.
Small Joints: Should be cooked and can then be
refrozen as cooked dishes.
Chicken: Should also be cooked and refrozen as a
fresh dish.
¥
The symbols on the drawers show different types
of frozen goods.
The numbers indicate storage times in months for
the appropriate types of frozen goods. Whether
the upper or lower value of the indicated storage
time is valid depends on the quality of the foods
and pre-treating before freezing.
9
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
Changing the light bulb
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED
CLEANING PRODUCTS OR WAX
POLISHES, TO CLEAN THE INTERIOR AS
THESE WILL DAMAGE THE SURFACE AND
LEAVE A STRONG ODOUR.
D731
Unscrew the light cover and then pull it outward
toward the middle of the cabinet. Unscrew the bulb
and replace it with a new 15 watt bulb (available
from your nearest Service Force Centre).
External cleaning
Wash the outer cabinet with warm soapy water. Do
NOT use abrasive products.
Replace the light cover by sliding it into its original
position and replacing the screw.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
Cleaning the crispÕn fresh filter
The filter is held by two small support frames which
press into position and are therefore easily removed
for cleaning. To do this, turn the glass shelf upside
down and release the frames as shown in figure.
The filter and the glass cover can be washed gently
in warm soapy water, they should not be put in the
dishwasher.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
Replacement filters can be purchased as a spare
part from your local Zanussi Service Centre.
CONDENSER
DEFROST
TRAY
COMPRESSOR
D273
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
D711
10
Defrosting
Refrigerator
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via a
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
D037
Freezer
When the frost has reached a thickness of up to
4mm it can be removed using the ice scraper
provided with the appliance. During this operation it
is not necessary to disconnect the appliance from
the mains and remove the food. Never use metal
tools for this operation.
For complete defrosting (once or twice a year)
proceed as follows:
-
turn the thermostat dial to the ÇOFFÈ position (O)
or disconnect the appliance from the mains.
-
Remove any food from inside the freezer and
fridge, wrap it in several sheets of newspaper and
store in a cool,dry place.
-
Leave the door open and insert the ice scraper
under the channel in the centre of the lower part
of the appliance; place a low-sided container
beneath the scraper to collect the water (see fig.).
-
-
-
Clean and dry thoroughly.
Replace the scraper in one of the drawers .
Reconnect the appliance to the mains or reset
the thermostat to the normal position.
-
After letting the appliance run for at least half an
hour, replace the previously removed food into
the compartment.
D068/2
Important
When defrosting the freezer, the fridge is also
controlled by the thermostat and will not be
operational during this period. A temperature rise of
the frozen food packs, during defrosting, may
shorten their safe storage life.
11
SOMETHING NOT WORKING
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made, even if the appliance is under guarantee.
Before contacting your local Service Force Centre, check the following points:
Symptom
Solution
No power to the appliance
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come on
Ensure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
The temperature in the fridge or freezer section is
too high
Check the thermostat control knob is turned to the
correct setting relative to ambient conditions.
Check the ambient temperature is within the
applianceÕs operating limits of 10¡C to 32¡C.
Relocate the appliance if necessary.
The freezer door will not open
Has door just been opened? If so leave for a few
minutes to allow the air pressure to equalise.
The compressor runs continously
Adjust the thermostat control knob to give correct
temperature control. See ÒSetting the temperatureÓ.
Check that the doors are closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Check that air ventilation is not obstructed.
Ensure the doors are not left open.
Excessive frost and ice has built up
Check that nothing is preventing the doors from
closing.
Is the door gasket intact and clean.
Has advised periodic defrosting been carried out.
Noise
Refer to normal operating sounds.
Water under the salad crispers
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
Low ambient operation
During prolonged periods of low ambient temperatures,ie;10¡C and lower, the compressor on single
compressor fridge freezers can remain inoperative during this time .
This is due to the air temperature within the refrigerator compartment being maintained at 6¡C or under thus not
calling the thermostat to energise the compressor .
12
During a normal night time period of approximately 8 hours a traditional fridge freezer can normally maintain the
frozen food temperature but if the appliance is left for longer period in a low ambient temperature the freezer will
defrost .
If, after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
Before calling out an engineer, please ensure you have read the details under the heading ÔSomething Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products,
please contact our Customer Care Department by letter or telephone at the address below or visit our website
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727 (*)
* calls to this number may be recorded for training purposes.
13
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturerÕs
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the CompanyÕs property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 29
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)1753 219 897
NŸrnberg
Pordenone
Stockholm
Slough
Sweden
UK
14
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
165
cm
Width
Depth
60
60
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
90 W
AVERAGE DAILY UNITS ELECTRICITY *
GROSS CAPACITY
0.8 kWh
Fridge
174 l
88 l
Freezer
NET CAPACITY
Fridge
170 l
77 l
Freezer
STAR RATING
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
15
INSTALLATION
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Important
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on ÒDoor reversalÓ.
Positioning
This appliance is designed to operate in ambient
temperatures between 10¡C (50¡F) and 32¡C (90¡F).
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10¡C (50¡F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
A
B
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4Ó) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
NP002
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
D200
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then re-tighten the screws.
PR153
16
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not
correspond with the markings identifying the
terminals in your plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
BROWN
BLUE
CORD CLAMP
D207
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
ÇEÈ or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter ÇNÈ or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter ÇLÈ or coloured
red.
17
Door reversal directions
1. Disconnect from the electricity supply.
F
E
2. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
F
F
3. Remove the ventilation grill (D).
4. Remove the plug (F) from the ventilation grill (D)
and replace it on the opposite side.
D
F
5. Unscrew the bottom hinge (E).
6. Remove the freezer door by releasing it from the
middle hinge (H).
7. Unscrew the middle hinge.
8. Remove the fridge door by releasing it from the
top hinge pin (G).
H
9. Remove the pin then mount these on the side,
after having removed the small plugs (I) which
should then be fitted on the opposite side.
10.Refit the fridge door and replace the middle hinge
to the left hand side.
11.Replace the door and bottom hinge (E) on the
opposite side.
12.Refit the grill (D) to the base of the product.
The doors can be aligned by adjusting the middle
hinge.
The middle hinge can be adjusted horizontally, after
having slackened the two screws with a screwdriver.
G
Important
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
I
I
I
Printed on recycled paper
18
© Electrolux Household Appliances Limited 2002
|