Wells Ventilation Hood WVSW VENTLESS HOOD User Manual

531

WELLS BLOOMFIELD, LLC

2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439

telephone: 775-689-5703

fax: 775-689-5976

www.wellsbloomfield.com

OWNERS MANUAL

MODEL

WVSW

VENTLESS

HOOD

For

CONVEYOR

WARMERS

Includes

INSTALLATION

USE & CARE

SERVICE

IMPORTANT: DO NOT DISCARD THIS MANUAL

This manual is considered to be part of the appliance and is to be given to the OWNER or

MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of

this appliance. Additional manuals are available from your WELLS DEALER.

THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR

INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any

questions concerning installation, operation or maintenance of this equipment.

PRINTED IN UNITED STATES OF AMERICA

p/n 305812 Rev. B

ECN-13380

M531 071101 cps

TABLE OF CONTENTS

WARRANTY

SPECIFICATIONS

FEATURES & OPERATING CONTROLS

AGENCY LISTING INFORMATION

PRECAUTIONS & GENERAL INFORMATION

INSTALLATION

OPERATION

CLEANING INSTRUCTIONS

TROUBLESHOOTING SUGGESTIONS

SERVICE INSTRUCTIONS

PARTS & SERVICE

CUSTOMER SERVICE DATA

INTRODUCTION

Thank You for purchasing this Wells Manufacturing Bloomfield appliance.

Proper installation, professional operation and consistent maintenance of this appliance will ensure that it

gives you the very best performance and a long, economical service life.

This manual contains the information needed to properly install this appliance, and to use and care for the

appliance in a manner which will ensure its optimum performance.

SPECIFICATIONS

FEATURES & OPERATING CONTROLS

WVSW VENTLESS HOOD

Fig. 1 Features & Operating Controls

FEATURES & OPERATING CONTROLS (continued)

ITEM

DESCRIPTION

CANOPY

Removable canopies aid in vapor capture at entry and exit of the conveyor

warmer. Canopies hang from mounting pins at each end of the hood.

ELECTRICAL

EXHAUST

The hood plugs into a NEMA 5-15R (120V) or 6-15R (208/240V) receptacle

with a 6' power cord. An illuminated power switch on the front panel is used

to start/stop the hood fan.

The hood uses an exhaust fan to provide air movement. The fan exhausts

through a screened opening in the top of the hood.

IMPORTANT: DO NOT block exhaust opening.

FILTERS

The hood uses two filters. A high efficiency filter is used to capture

particulate emissions.

A charcoal filter is used to help control odors.

Filters are accessed by opening a hinged panel on the front (operator's)

side of the hood.

Filter operation is monitored by a vacuum switch. When the filter(s)

become loaded to the point of being unable to remove particulates, a front

panel "change filters" indicator will glow.

NAMEPLATE

TOP PANEL

Provides Manufacturer, Model and Serial Number information.

Also, provides electrical ratings.

CAUTION!

ELECTRIC SHOCK HAZARD

EXPOSED ELECTRIC CIRCUITS

Top panel must be opened ONLY by qualified personnel.

Allows access to interior components.

DO NOT stack anything on top of the hood.

AGENCY LISTING INFORMATION

This appliance conforms to NSF Standard 4 for sanitation only if installed

and maintained according to the instructions in this manual.

STD 4

This appliance is

Listed for 120V and 208 - 240V.

IMPORTANT: For use with conveyor warmer of 9,000 watts maximum.

NOTE: This ductless hood has not been evaluated to the requirements of

NFPA 96.

Local jurisdictions may require additional evaluations for installation

of this product.

PRECAUTIONS AND GENERAL INFORMATION

This appliance is intended for use in commercial establishments

only.

WARNING:

ELECTRIC

SHOCK HAZARD

This appliance is intended as a smoke and odor control device,

designed for use with specified warming equipment. No other use is

recommended or authorized by the manufacturer or its agents.

All servicing requiring

access to non-insulated

electrical components

must be performed by a

factory authorized

Operators of this appliance must be familiar with the appliance use,

limitations and associated restrictions. Operating instructions must be

read and understood by all persons using or installing this appliance.

technician.

Cleanliness of this appliance is essential to good sanitation. Read and

follow all included cleaning instructions and schedules to ensure the

safety of the food product.

DO NOT open or remove

the top panel. Failure to

follow this warning can

result in severe electrical

shock.

Disconnect this appliance from electrical power before performing any

maintenance or servicing.

DO NOT submerge this appliance in water. This appliance is not jet

stream approved. Do not direct water jet or steam jet at this appliance,

or at any control panel or wiring. Do not splash or pour water on, in or

over any controls, control panel or wiring. Do not wash floor around

this appliance with water or steam jet.

CAUTION:

RISK OF

DAMAGE

DO NOT connect or

energize this appliance

until all installation

instructions are read and

followed. Damage to the

appliance will result if

these instructions are not

followed.

Exposed surfaces of this appliance can be hot to the touch and may

cause burns.

The technical content of this manual, including any wiring diagrams,

schematics, parts breakdown illustrations and/or adjustment

procedures, is intended for use by qualified technical personnel.

Any procedure which requires the use of tools must be performed by a

qualified technician.

This manual is considered to be a permanent part of the appliance.

This manual and all supplied instructions, diagrams, schematics, parts

breakdown illustrations, notices and labels must remain with the

appliance if it is sold or moved to another location.

CAUTION:

HOT SURFACE

Exposed surfaces can be hot

to the touch and may cause

burns.

This appliance is made in the USA. Unless otherwise noted, this

appliance has American sizes on all hardware.

INSTALLATION

UNPACKING & INSPECTION

NOTE: DO NOT discard

the carton or other packing

materials until you have

inspected the hood for hidden

damage and tested it for

proper operation.

Refer to SHIPPING DAMAGE

CLAIM PROCEDURE on the

inside front cover of this

manual.

Carefully read all instructions in this manual before starting any

installation.

Carefully remove the hood from the carton.

IMPORTANT: Appliance weighs 92 lbs (42.7 kg). Use appropriate

care when removing from carton and installing on conveyor warmer.

Remove all protective plastic film, packing materials and accessories

from the hood before connecting electrical power or otherwise

performing any installation procedure.

Read and understand all labels and diagrams attached to the hood.

WARNING!

RISK OF

INJURY

Carefully account for all components and accessories before

discarding packing materials. Store all accessories in a convenient

place for later use.

Installation procedures must

be performed by a qualified

technician with full knowledge

of all applicable electrical

codes. Failure can result in

personal injury and property

damage.

COMPONENTS:

HIGH EFFICIENCY FILTER

CHARCOAL FILTER

COMPONENTS SHIPPED SEPARATELY

CANOPY (2 ea)

ADAPTER TOP

CAUTION!

RISK OF

INJURY AND

PROPERTY

DAMAGE

SETUP

The conveyor-style warmer requires an adapter top (shipped

separately) for mounting the hood. Place adapter top on warmer

before setting hood in place. Carefully place hood on top of warmer.

Orient hood so that power switch is on the same side as the power

switch of the warmer. Center hood over the body of the warmer as

shown in Fig. 2 below:

Unplug conveyor warmer and

allow to cool before beginning

installation.

IMPORTANT:

Maintain required clearances

of at least 6" between the

appliance and adjacent

combustible surfaces.

Avoid storing flammable or

combustible materials in, on

or near the appliance.

Fig. 2 Hood installation on warmer

Check high efficiency filter and charcoal filter for proper installation.

Charcoal filter slides into clips on the high efficiency filter. Airflow

marks must point "up".

Attach entry and exit canopies to pins on sides of hood. Canopies are

interchangeable and may be mounted at either end.

Maintain required clearances of at least 6" between the appliance and

adjacent combustible surfaces.

INSTALLATION (continued)

ELECTRICAL INSTALLATION

WARNING!

ELECTRIC

SHOCK HAZARD

Refer to the nameplate. Verify the electrical power source. Voltage

and phase must match the nameplate specifications. Plugging the

hood into the wrong voltage can severely damage the unit .

All servicing requiring

access to non-insulated

electrical components

must be performed by a

factory authorized

Your hood is equipped with a grounded electrical cord. This cord

must be plugged into a properly grounded NEMA 5-15R (120V) or

NEMA 6-15R (208/240V) single phase receptacle.

technician.

DO NOT open any access

panel which requires the

use of tools. Failure to

follow this warning can

result in severe electrical

shock.

CAUTION!

ELECTRICAL

SHOCK HAZARD

The ground prong of the

power cord is part of a

system designed to protect

you against electric shock in

the event of internal damage.

DO NOT cut the ground

Fig. 3 Electrical Plug and Receptacle Configuration

prong (large round prong) or

twist a blade to make the plug

fit an existing receptacle.

IMPORTANT:

Contact a licensed electrician

to install and connect

electrical power to the

appliance.

IMPORTANT:

Damage due to being

connected to the wrong

voltage or phase is NOT

covered by warranty.

OPERATION

OPERATING CONTROLS

Controls include a lighted POWER SWITCH and an amber REPLACE

FILTER indicator light.

Press POWER SWITCH to ON anytime conveyor warmer is operating.

When power is first turned on, the REPLACE FILTER light will glow.

As the fan comes up to speed and air flow is established, the REPLACE

FILTER light will go out.

If the REPLACE FILTER light does not go out, the filters must be

replaced. However, the fan will continue to operate when the

REPLACE FILTER light is lit.

Fig. 4 Operating Controls

FILTER REMOVAL AND INSTALLATION

CAUTION!

RISK OF INJURY

Disconnect power from hood and conveyor warmer before servicing

filters.

Disconnect power from hood

and conveyor warmer before

servicing filters.

Remove screw from filter access panel on front (operator's) side of

hood. Slide filter pack (high efficiency filter and charcoal filter) from

filter chamber.

IMPORTANT:

DO NOT store anything on

top of the hood.

Slide new filter pack into filter chamber. Be sure airflow markings on

both filters point "up".

DO NOT block the exhaust

opening.

Close access panel and reinstall screw.

IMPORTANT:

Filters are disposable. Never attempt to wash either filter.

Filters will absorb water if washed, causing food contamination and

possible equipment damage.

Both the high efficiency and

charcoal filters must be in

place at all times during

operation.

Fig. 5 Filter Installation

CLEANING INSTRUCTIONS

PREPARATION

Unplug hood and conveyor warmer

Allow to cool completely before cleaning

CAUTION!

RISK OF INJURY

FREQUENCY

TOOLS

Daily

Disconnect power

from hood and conveyor

warmer before cleaning.

Mild Detergent

Soft Cloth or Sponge

IMPORTANT: DO NOT spill

or pour water into controls,

control panel or wiring.

1. Disconnect power from hood and conveyor warmer before cleaning.

2. Remove entry and exit canopies. Canopies may be washed in a

sink or dishwasher. Rinse and dry canopies thoroughly.

DO NOT spill or pour water

into exhaust opening.

3. Wipe interior and exterior surfaces of hood with a soft cloth or

sponge dampened with water and a mild detergent.

DO NOT submerge hood in

water or wash with water or

steam spray. Damage to

internal components will

occur.

Damage to internal

components from water

damage is not covered by

warranty.

IMPORTANT:

Never attempt to wash either filter.

Filters will absorb water if washed, causing food contamination and

possible equipment damage.

4. Rinse all washed areas by wiping with a clean soft cloth dampened

with clean water. Dry with a soft cloth.

5. Reinstall entry and exit canopies.

Procedure is complete

TROUBLESHOOTING SUGGESTIONS

SYMPTOM

PROBABLE CAUSE

CORRECTIVE ACTION

Plug cord into appropriate power

receptacle.

No operation, no lights

Cord unplugged

Circuit breaker off or tripped

Damaged power cord or plug

Damaged power switch

Filters dirty

Reset circuit breaker

Replace power cord

Replace power switch

Replace filters

REPLACE FILTER light remains

lit (never shuts off)

If filters are clean

and fan is operating

New filter still in plastic wrapper

Exhaust opening blocked

Filter opening blocked

Vacuum hose kinked

Vacuum line plugged

Damaged vacuum switch

Fan jammed

Remove plastic wrapper

Clear or clean exhaust duct and

opening

Clear filter opening

Unkink vacuum hose

Clean or replace vacuum line

Replace vacuum switch

Unjam fan

If fan is not operating

Damaged motor start capacitor

Damaged fan motor

Replace start capacitor

Replace fan motor

SERVICE INSRTUCTIONS

IMPORTANT:

VACUUM DIAGRAM

DO NOT store anything on

top of the hood.

DO NOT block the exhaust

opening.

Filter operation is monitored

by a vacuum switch and a

system of vacuum hoses.

The switch energizes the

REPLACE FILTER light if

airflow through the filters is

insufficient for efficient

operation. The light is a

warning only, and does not

control the operation of the

hood.

WIRING DIAGRAM

PARTS & SERVICE

IMPORTANT: Use only

DESCRIPTION

PART NO.

factory authorized service

parts and replacement

filters.

For factory authorized

service, or to order factory

authorized replacement parts,

contact your Wells authorized

service agency, or call:

HIGH EFFICIENCY FILTER 16 x 20x 4

22862

22403

CHARCOAL (CARBON) FILTER 14 x 20 x 7/8

Wells Bloomfield, LLC

2 Erik Circle

P. O. Box 280

Verdi, NV 89439

Service Parts Dept.

phone: (775) 689-5707

fax:

(775) 689-5976

Service Parts Department can

supply you with the name and

telephone number of the

WELLS AUTHORIZED

SERVICE AGENCY

nearest you.

CUSTOMER SERVICE DATA

please have this information available if calling for service

RESTAURANT _____________________________ LOCATION _____________

INSTALLATION DATE ________________________ TECHNICIAN ___________

SERVICE COMPANY ________________________________________________

ADDRESS ___________________________ STATE ______ ZIP__________

TELEPHONE NUMBER (_____)_____-_________

EQUIPMENT MODEL NO. _______________

EQUIPMENT SERIAL NO. _______________

VOLTAGE: (check one)

120

208

240

Commercial Food Equipment Service Association

Wells Bloomfield proudly supports CFESA

Commercial Food Equipment Service Association

SERVICE TRAINING -- QUALITY SERVICE

Genuine Parts

Protect - YOU - All - Ways

CUSTOMER SATIISFACCTION

WELLS BLOOMFIELD, LLC

2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439

telephone: 775-689-5703

fax: 775-689-5976

www.wellsbloomfield.com

PRINTED IN UNITED STATES OF AMERICA

Weslo Treadmill WLTL39093 User Manual
West Bend Fondue Maker ELECTRIC FONDUE POT User Manual
Westinghouse Microwave Oven WCM770B W User Manual
Whirlpool Clothes Dryer WGD9200SQ0 User Manual
Whirlpool Microwave Oven AMW 440 User Manual
Wilton Cordless Saw JWBS 16B User Manual
Yamaha Electronic Keyboard EZ J200 User Manual
Zanussi Clothes Dryer TD 100 User Manual
Zanussi Freezer 42FF User Manual
Zanussi Oven ZUF 270 User Manual